Recent posts

You can visualize the sq ft of each floor using the following resources:
1 - You can use Design => Active Floor Area => Status bar (bottom of the screen - pointed with a red arrow in the image below) => visualize the area of the current floor.

Sq Ft.jpg

2 - Use the Estimator Power Tool => visualize the area by floor, by room, etc.

Hope this helps.

#64

V17 - 2026 Looking for Help? / Calculate total Square footage

Last post by CFI - June 06, 2024, 11:18:25 AM

Is there a way to calculate square footage without measuring and adding up each room? I haveremoved a few rooms and walls.

I have TurboCadFloorplan 2019

#65

V17 - 2026 General Discussion / Re: Odd "planes" in 3D object

Last post by Patricia G. - June 03, 2024, 10:34:06 AM

Hi Jeff,

Quote from: JOD on June 03, 2024, 08:14:34 AMThe part of your first sentence "So, you have points on different axes, therefore you must verify each point to solve the issue" has me mystified. Can you explain how to "verify each point"?

If you have a 4 points plane on the X axis and one of the points was moved on the Y axis, you will see these phantom surfaces. To verify the points => edit each surface by points (page 434 of my eBook) and see if one of the points is out of the surface / axis.

Quote from: JOD on June 03, 2024, 08:14:34 AMI have ben using the revolve tool for making circular objects which have a hole in the middle... i.e. a "donut". Can you bend a 6 foot long straight tube in the center (at 3 foot) and have a 3" radius at the bend?

To bend => adjust the curvature. Or create a separate piece for the curve using the Revolve tool (90°).

Hope this helps.

#66

V17 - 2026 General Discussion / Re: Odd "planes" in 3D object

Last post by JOD - June 03, 2024, 08:14:34 AM

Hi Pat,

Thank you for your reply. The part of your first sentence "So, you have points on different axes, therefore you must verify each point to solve the issue" has me mystified. Can you explain how to "verify each point" or refer to a page in either the User Guide or Pat's eBook for V2022 for help understanding this?

I do have your eBook for V2022 and will review the revolve tool. I have ben using the revolve tool for making circular objects which have a hole in the middle... i.e. a "donut". Can you bend a 6 foot long straight tube in the center (at 3 foot) and have a 3" radius at the bend?

Again, thanks for the help.

Jeff O

#67

V17 - 2026 General Discussion / Re: Odd "planes" in 3D object

Last post by Patricia G. - June 02, 2024, 03:55:53 PM

Hi Jeff,

I saw the problem as well as an additional issue, as you can see in the image below.

I confirmed these results with one of the programmers: if you take a 4 point plane and move / curve the points on different axes you'll get different results. So, you have points on different axes, therefore you must verify each point to solve the issue.

Regarding your question "is there an easy way to bend tubes, shafts or square tubing?" => create the curved segment using the "Revolve" Tool.

If you have my eBook for FP V2022, check the 3D custom Workshop chapter. The revolve tool is on page 452.

Hope this helps.

#68

V17 - 2026 General Discussion / Re: Odd "planes" in 3D object

Last post by JOD - June 02, 2024, 12:13:06 PM

I think I used a chair object similar to this from TFP 2017v and revised the seat cushions and bent the metal frame to a chair that we have. I have had a lot of difficulty trying to bend various long "tube" shapes as needed for various frame works.

Jeff O

#69

V17 - 2026 General Discussion / Re: Odd "planes" in 3D object

Last post by Patricia G. - May 30, 2024, 06:31:52 PM

Hi Jeff,

I opened your file. I found some issues.
Did you create this chair from scratch or did you import the file?

#70

V17 - 2026 General Discussion / Re: Odd "planes" in 3D object

Last post by JOD - May 30, 2024, 06:09:22 PM

Hi Pat,

I have made a small house and inserted the problem chair object into the floor plan. I think I have followed your instructions correctly. If not, please advise.

Jeff O

Pages 1 ... 5 6 7 8 9 10